Plumbing Services

How to Do Faucet Repair Yourself

Faucet repair can be done quickly and inexpensively, especially if you replace washers, o-rings, and gaskets. You can also fix leaks by replacing the valve seat and cartridge. To do this, you need to remove the handle and escutcheon. You can use a flathead screwdriver or hex wrench to loosen the screws.

Faucet Repair

The seals that keep water flowing through a faucet can degrade and break, leading to leaks. These problems are usually the result of regular use and water mineral deposits that can corrode these parts. Routine maintenance and cleaning can help prevent these issues. However, if the problem persists, you may need to replace the valve seat or other factors. A professional at Plumbing Express, Inc. can diagnose and fix a leaking faucet.

A leaking faucet handle is usually caused by a worn out O-ring or a seal. The O-ring fits around the inner brass body beneath the outer faucet housing and helps to keep water inlet and outlet seals intact. If the O-ring wears out, water can leak down into the handle and cause it to drip. To fix this, simply match a replacement O-ring to the size of the old one and coat it in nontoxic plumber’s grease.

Leaks from the spout

Water sediments can erode the valve seat that connects the faucet to the spout. This can create small crevices that allow water to seep through and cause a leak. The spout may also leak if the washer that rests against the valve seat has been damaged or improperly installed. Fortunately, these parts can be replaced relatively easily, and you should be able to find a kit that is compatible with your faucet.

Leaks from the handles

The most common cause of a leaking faucet handle is the gasket. This is a small rubber ring that fits between the handle and the base of the faucet, and it can become hard and brittle over time. This can lead to a loose fit and allow water to leak past the handle and into the sink. To fix this, remove the handle and clean the area where the adjusting ring and packing nut are located. Once they are loose, tighten them using the spanner tool that comes with your repair kit. Make sure to dry the area thoroughly before reassembling the faucet. You should also replace any decorative covers before turning the water back on.

Rust and grime

Rust is not just unsightly; it can be harmful to your health. It can also lead to a number of problems with your faucets and plumbing. The best way to prevent rust is by cleaning frequently and using a mild cleanser. You should also avoid using any abrasive scrubbers or cleaners. You should also rinse the faucet well after cleaning to remove any traces of cleanser.

Bathroom faucets are in constant contact with water and can be particularly prone to rust and mineral buildup. This is because the water in your home may contain high levels of iron and calcium. In addition, if the faucets are exposed to air and sunlight for long periods of time, they can become more susceptible to rust. Rust stains can be removed by applying a metal polish to the surface of your faucets.

A rusted faucet handle can be a real eyesore and can make your whole bathroom look untidy and disorganized. The rusted area of the handle can also be difficult to clean, especially if the faucet is in an awkward position. If the rust is only on the handle and not the faucet head, a squirt of penetrating oil can usually loosen it. Then, a good set of channel lock pliers can usually free the handle from the faucet.

For older, fully set rust stains that regular cleaning methods do not remove, you can use a solution of oxalic acid and talc to make a paste. This can be bought in crystal form at a hardware store and is very toxic, so you should wear rubber gloves and eye protection when using it. You should then apply the paste to the rust stains and allow it to sit for half an hour before scrubbing.

Decorative iron fixtures like sinks and bathtubs are susceptible to rusting, which is why they should be sealed. In some cases, a rust spot on your bathroom faucet can indicate a problem with the water pipes in your home, so it’s important to contact a professional for assistance. In most cases, the rust is caused by sediment that is being pushed through the pipes from other sources of water in your home.

Damaged parts

A faulty cartridge or stem can be a big problem for your faucet. The best thing to do is call a plumber in Katy, TX to replace it as soon as you notice any signs of damage. If you don’t, the rust and corrosion can damage other parts of the faucet, leading to leaks and poor water quality.

To fix the problem, start by turning off the water to the faucet and draining it. Then, turn off the valves under the sink to prevent water from flowing into the house. Next, you’ll need to disassemble the faucet to get to the damaged parts. This process can be tricky, but it’s important to follow the instructions carefully. This will ensure that you don’t damage any of the parts. Before disassembling your faucet, make sure you have the following tools:

A bucket or towel: This is essential for catching any water that may spill during the repair process. You should also have a set of pliers to grip and twist tight or stubborn nuts and bolts. A screwdriver: This is useful for removing the handle and hex screw from the top of the faucet body. A spanner tool: This is useful for loosening the adjusting ring on some faucets. A replacement adjusting ring: This is a small ring that covers the hex screw, and it’s usually made of brass. This can be purchased online or at most hardware stores.

Once you’ve removed the handle and cap, it’s time to remove the stem. First, you’ll need to unscrew the hex screw on the handle using an Allen wrench. Then, you’ll need to loosen the cam nut or adjustable ring on the bottom of the stem with a wrench. You can then lift out the plastic disc and the rubber seats and springs. If your faucet has a ceramic disc, you’ll need to unscrew and replace it.

If you’re still experiencing a leak, it might be due to a damaged O-ring. This is a common cause of faucet leaks. They can range in size from 3/8 to 5/8 of an inch, so you’ll need to find a new one at a home improvement store. Be sure to coat the O-ring with nontoxic, heat-proof plumber’s grease before replacing it.

Cost

The cost of repairing a leaky faucet can be quite expensive, depending on the type of faucet. One-off repairs may not be as bad, but repeated problems can quickly add up to more than the cost of a new faucet. The good news is that you can repair most types of faucets yourself, although professional help is always recommended if the damage is extensive or your home’s water is hard.

The first step is to shut off the water supply, if you haven’t already. Next, remove the handle. Some handles are held in place by a screw on the top or back, and others have a small metal button that snaps out. If the button doesn’t come out easily, use a screwdriver to unscrew the tiny screws that hold it in place. Penetrating oil can also help loosen the screw. Once the handle is removed, you should see a packing nut. Unscrew this with a wrench or large slip-joint pliers, being careful not to scar the metal. Once the nut is off, you can remove the stem. The washer at the bottom of the stem is the seat washer, and it may be responsible for the leak. Replace this with a new one, and coat the O-ring with nontoxic, heat-proof plumber’s grease to prevent future leaks.

If the spout is leaking from its base, then you will need to replace the springs and seats. To do this, remove the handle and screw cover. Wrap a pair of slip-joint pliers’ jaws with duct tape to protect them from any damage as you unscrew the set screw that holds the handle in place. Unscrew the dome assembly and handle adapter. Finally, remove the handle and plastic pivot stop.

Cartridge-style faucets are a bit more complicated to fix, but you can usually do it yourself. If you can’t get rid of drips at the spout, then you will need to remove the cartridge and either replace the O-rings or the entire cartridge. You can find replacement parts at hardware stores, home centers, and plumbing supplies specialists.